Tweak Your Tank


           Tweak Your Tank
           By: Jeff Shoemaker
           Originally Appeared in Winemaker Magazine Aug/Sept. 2014  
 
 

In the past few years I have made larger ­­­and larger batches of wine, as a result the number of carboys I use has really racked up. Each year I try to make improvements to my home winery and being a total wine equipment nerd, variable capacity stainless steel tanks were an obvious upgrade for me. What better way to make the next step than to have a big, shiny tank or two in my Wine cellar? I set out to research the tanks and soon realized while there are benefits, there are certainly just as many drawbacks. However, with some effective modifications, and the purchase of a few pieces of equipment, you can increase the usefulness of the tanks. I have invested time learning how the tanks work, and what modifications others have used to improve on the successful and trouble free use of the tanks. This article caters to the home winemaker with hopes to improve their experience with stainless steel variable capacity tanks. I will elaborate on these issues and help you get the most out of your beautiful wine tank.
 

Tank Modifications:

There is much debate on whether or not to perform long term aging in these tanks due to the possibility of lid failure or oxygen exposure through various parts of the tank. However, I am confident that with the following alterations, you can do more with your tank than just fermentation, malolactic fermentation or a short stay before the barrel. Please read on and get your tank into shape and ready for the long haul! 
 

Lid Bladder/ Gasket:

When your new tank arrives, the lid gasket/bladder it comes with will most likely be one made of a thin, clear vinyl material. Though these gaskets are fine for fermentation when the CO2 is protecting the wine from O2, they cannot be trusted for any post fermentation storage because they form a poor seal around the lid when inflated. Another vulnerable part of the gasket is the seam where the two ends meet to form the seal. (Please see picture)  The major problem with the seam in the stock gasket can be seen in a simple water test. All you need to do is put a gallon of water in your tank and put the lid in the tank near the top and inflate the gasket up to about 0 .6 bars. Then put the tank on its side and angle it allowing the water to hit the lid while gently rolling the tank back and forth, and watch for any leaks. Most likely water will come leaking out where the seam is, which means an airtight and uniform seal has not been achieved.  These leaks will show you where O2 can get to your wine. I would also recommend this test when you get the upgraded gasket to ensure a good seal.
 
This seam allows oxygen into the tank
These issues will allow harmful oxygen exposure to interact with your wine. A way to remedy this is to replace the lid gasket with a new and improved one. These well-constructed lid gaskets are made from thick, heavy duty food-grade rubber; they are a major upgrade over the stock gaskets. Another great thing about them is they are seamless and come equipped with a metal nozzle. This metal nozzle allows you really tighten the pipe clamp to ensure an airtight seal.



There are two different lid gaskets you’ll see when shopping; white and black. I personally use the black ones because they fit my particular tank. As for the white ones, I have heard nothing but good things. I suggest you pick the one that fits your tank the best.

When you decide to get a new gasket, measure the diameter of you tank lid and allow these two fine wine shops to assist you in getting a gasket that is a perfect fit.

You can find them here:

Morewinemaking.com - Item #: WE369C (White gasket)

Vintner Vault – TK-002006 (Black Gasket) 

The Stock airlock
Photo Courtesy of Westchester Amateur
Winemakers
The waterless airlock that comes with most tanks uses a marble over the vent hole to allow gas to escape and is supposed to re-seat in the hole to prevent oxygen from getting back in. This is another entry point for oxygen and should not be relied upon to protect your wine. A couple things you can do to improve this are:
 
-You can take the existing marble airlock and cut it in half just below the vent. This gives you a place to put a bung and an airlock, or a breathable bung.
 
-Consult a welder to have a stainless steel tri-clamp ferrule installed in the lid. This allows you to use an airlock, breathable bung, or tank vent (Navigate to –stpats.com – vent 211.) Tri-clamp ferrules also give you the ability to use hoses or caps when the ferrule is not in use, and more than one can be installed! 
Photo Courtesy of Westchester Amateur
Winemakers
 
       Isolating the Pump
Photo Courtesy of Westchester
Amateur WineMakers 
The pump used to inflate the gasket is another source of problems due to the fact air can leak out of the threaded valve on the side of the pump, around the gauge and out of the thin tubing which can be cut from the pipe clamp. One solution is to first; get thicker tubing that a tightened pipe clamp can’t cut through. As for the leaky pump; an inline pressure gauge and a shut off valve between the pump and the lid gasket can be installed.  By doing this you remove the pump completely, your lid gasket stays inflated and the gauge allows you to monitor the inflation level of the gasket so you know when to pump it up again. When the gasket needs inflated hook the pump up to the shut off valve, turn it to the on position and pump it to the desired level. Then turn the valve to off position prior to unhooking the pump. 


If you have several tanks you can install a quick disconnect, (morewinemaking.com Item #: H550.) Rather than buying a pressure gauge for each tank, you can quickly connect the pump to the lid gasket via the quick disconnect and use the pump gauge to check the pressure on each tank. This works by hooking one side of the quick disconnect to the gasket’s metal valve with a piece of suitable tubing and pipe clamps to ensure a tight fit. Then connect the other side of the quick disconnect to the tubing of the pump in the same fashion. After the quick disconnects are installed, connect them and inflate the gasket to a suitable level (I like about 0.6 bars) and unhook the pump and store it until the next time you need to perform a check. This keeps Jr. winemakers, like my 2 year old son from banging the pump of the side of tank!

                                                     
                                                   Temperature fluctuations and Using an Inert Gas Bleeder
 Being that we make our wine in passive cellars, garages or our kitchens, maintaining and managing a consistent temperature can be difficult.  Temperatures can fluctuate throughout the time the wine is in storage. These temperature vacillations are apparent in the varying wine levels in the neck of a carboy.  When using a stainless steel tank, temperature swings can cause the tank to actually expand and contract. Or the lid could be sucked in by a vacuum from a contracting tank causing the lid to fail exposing your wine to excessive oxygen. To help with this you could use an inert gas bleeder system (morewine Item #: WE399.) Included in this purchase are the tank lid connection and the diaphragm bleeder regulator. You will need to supply the inert gas tank, tubing and gas tank regulator.  
 

How this mechanism works is if the temperature increases and the wine expands; the excess pressure will be released out of the diaphragm bleeder. While at the same time the bleeder is allowing inert gas to be pulled into the tank on demand, without putting pressure on the tank. Please go to Morewinemaking.com Item #WE399 for more information. Being able to perform long term storage in these tanks is like a dream come true. For the home winemaker on a budget, this particular upgrade may seem like an unnecessary luxury. But this is an important upgrade if you plan to use your variable capacity tank for long term storage of wine. By only using your tank for fermentation, malolactic fermentation and some other short term uses, you are limiting the tanks overall usefulness and not really getting the value for your money.  My goal for Poni Home Winery is to replace most of my carboys with tanks which will make it easier to utilize my time more efficiently and reduce the strain on juggling family, work and reading Batman comics. It also allows me to use my limited space more effectively.  
 

The Drain Valve
If your plan is to quickly move your wine via the drain valve on the bottom of the tank, you may wish to replace the standard valve that comes on the tanks.  Your options are a full port ball valve or a tri-clover ferrule and clamp with a butterfly valve. These upgrades are necessary when wanting to move larger volumes of wine faster, or through a larger pump. For transfers in and out of the tank I personally use ½” tubing which is lowered into the tank and I transfer out with a pump that moves three gallons per minute (more on this later.) But if you want to use larger tubing and a larger pump, these upgraded valves are may be a good idea for you. As I mentioned earlier you will need to recruit the help of an experienced welder to help you in installing the T.C. ferrules etc. Tip: If you decide to use the drain valve that comes with the tank, use Teflon tape around the threads to keep it from leaking. 
 
Additional Upgrades You May Consider Are:
-Lid handles: There is not much to hold onto when lowering the lid onto the wine preventing you from splashing grapey goodness all over the place. A good idea would be to have your now new friend the welder install two handles onto the lid. 
 

Photo Courtesy of Westchester Amateur
Wine makers
- Dust cover: A dust cover is a smart solution to the problem of dust and dirt settling on to the lid and on the exposed sides of the tank. The dust cover will also help with fruit flies, because they just love to hang around tanks filled to the brim with delicious wine! This could be anything from a bouffant cap from a hospital, a bed sheet or a plastic cover with an elastic edge. Really any of these options will do, and safeguard your wine while it is in the tank.  
-Tank Stand:  Any place you can buy your wine tank from will have stands available to put your tank on. Really all the stand is doing is getting the tank up off the floor, and for less than half the price you can build your own stand using 2 x 4” boards and ¾” plywood. You can build it just high enough so it is off the floor, or if you prefer to gravity rack, you can customize your stand to suit those needs These tanks when full of wine can be very heavy so please be sure of the stability of your newly made stand before using it full time. Some folks actually make wheeled carts for their tanks for ease of moving the tank about the winery. Just do whatever fits your needs best.
 

Equipment Needed to Use the Tank:

In order to use these tanks, you need to get some additional equipment to do various operations such as transfer the wine in and out of the tank, and clean it. Some of these things are necessary, and some are just nice to have.  
 

Pump: I use a self-priming diaphragm pump that can move three gallons per minute. It has a self-regulating motor which is designed to temporarily shut down, and then turn back on when restriction pressure exceeds pump capacity. This pump does not have a switch, so in order control the pump, I wired a common light switch into a heavy duty extension cord, which I can carry around as I am managing pump operations. This allows me to control the pump without having to run to the outlet to unplug it at the right time. This is plugged into a GFCI outlet for safety.   
 
Tubing: I use ½” tubing with the Buon Vino pre-filter on the inflow side of the pump which will protect the pump from debris, along with a racking cane on the end to prevent curling of the tubing in the donor vessel. On the outflow side of the pump is a ball valve to control the flow of the wine. This flow control is helpful if racking in or out of carboys.   


Stirring the Pot:
  As your tanks get bigger and deeper, you may find the long handled spoon you have is not adequate. A good substitute is a cordless drill mounted mixing paddle, you can find these at several winemaking stores, but Winery-equipment.com is the only place I know of that will make them at different lengths for you upon request.  

Keeping your tank and its parts clean is a priority. To make the job easier use a hose with a multi-sprayer to assist removing any debris that has built up in the tank. Working near a floor drain is also helpful because you can just tip the tank over to drain rinse water out, rather than trying to manage a tank over a sink. Going outside is also an option for tank cleaning, but not in Pennsylvania in February…  Brrrr!

As you gain experience with using these tanks; they will become just as easy as using a carboy. But a few things need to be remembered when using these wonderful tanks.



-They are not just set and forget: The tanks needs monitored every few days or once a week at the very least to check on the inflation level of the lid gasket and the integrity of the lid in general . Once you feel comfortable with using the tanks, your compulsive lid check s may become less and less, but they require regular inspections every once in while, this is very important.



- Regular SO2 monitoring is an absolute must: Even after most  of these modifications have been made, like any other vessel some  O2 may slowly find its way into the tank. This means when  considering buying a tank, you'll also need to consider a free sulfite testing kit. Whether it's the Vinmetrica sc-100 or the aeration oxidation kit, it is very important you have this available to you to prevent oxidation to your wine.



-Samples for testing and tasting:  When using the drain valve to pull samples for tasting or testing, the lid must be reseated e.g. the gasket must be deflated and then inflated again. These tanks don't act as wine kegs where you keep a volume of wine in the tank and just drink from it as you wish. If you plan to make a sulfite addition after a testing session, or any other addition for that matter, just reseat the lid after your testing session has ended and you've made you additions.



-Cleaners: Cleaners such as sulfite or bleach should not be used; they can cause pitting in the stainless steel, which will weaken the tanks. A good cleaning protocol to follow is: A hot water rinse, followed by your favorite cleaner such as Powdered Brewery Wash or One Step Cleaner (follow manufacturer's  instructions.) Follow with a no-rinse sanitizer or citric acid rinse solution of 50g-4 liters and then a final warm water rinse. You may sanitize the lid components, bungs and airlock at this time also using the same method as above.

In conclusion: Once the bugs are worked out, stainless steel tanks are very nice to have in the cellar. They take up less room, easy to clean, you are making additions to one vessel rather than several carboys, and they are very flexible if doing different volumes of wine each year. I hope this article will help you with your tank, or help you feel better about taking the plunge and getting one for yourself.


A very special thanks to the folks at Westchester Amateur Winemakers for their assistance in this article.

To purchase this back issue please visit https://winemakermag.com/product/314-august-
september-2014-issue



2 comments:

  1. Great write-up, I am a big believer in commenting on blogs to inform the blog writers know that they’ve added something worthwhile to the world wide web!..
    Chandeliers

    ReplyDelete
  2. Thank you! It's much appreciated

    ReplyDelete

Make It Fizz!

Make It Fizz! By: Jeff Shoemaker  This article originally appeared in the  Jun/Jul 2019 issue of Winemaker Magazine    Making ...